Homemade table saw (Part 4) – MITER slots using T-Tracks | ROUTER guide

Homemade table saw (Part 4) – MITER slots using T-Tracks | ROUTER guide

Community:
Website: https://goo.gl/9wZcs1
Instagram: https://goo.gl/1TnxKW
Facebook: https://goo.gl/H7L72E
Patreon: https://goo.gl/5pm5qs
Twitter: https://goo.gl/fzWWcA

How I made the miter slots on my homemade table saw. Also a link to how I figured out the router guide diagram.

.:| Router guide diagram |:.

http://www.willysgaragenorway.no
http://willysgaragenorway.no/tsr4measurements/

.:| Products used in this video |:.

T-track t-slot 800mm:
https://www.banggood.com/custlink/DGvvIIWekI
Machifit 10pcs M6 T Slot Nut T-Track:
https://www.banggood.com/custlink/m3GvZ8WAtG
Machifit 10pcs M8 T Slot Nut T-Track:
https://www.banggood.com/custlink/KmKvZSrsPF
1/2 Inch (12.8mm) Straight Dual Edged Cutter Router Bit:
https://www.banggood.com/custlink/3DmDISWNtM

.:| Other products used in this project |:.

Pocket hole jig:
https://www.banggood.com/custlink/GmGmHKLrbP
90 Degree Right Angle Clip:
https://www.banggood.com/custlink/KKKKVGLcs4
12inch Triangle Square Tool:
https://www.banggood.com/custlink/D3D3VGorQM
16pcs 15-35mm Forstner Drill Bit Set:
https://www.banggood.com/custlink/mGKvV3jJnf

Music:
https://www.epidemicsound.com/

8 Comments

  1. SmartTech on November 11, 2022 at 4:45 am

    From where i can get t slot channel in india ?



  2. ZK_63 on November 11, 2022 at 4:53 am

    Wow, you must have really had the inspiration bug. I have an older saw though it is even older than yours and just as much a piece of junk though it does get the job done. But I think i would have just gone out and bought a new saw. I really like what you have done though and I am planning on upgrading mine to a new top at least since the miter slots are junk. Thanks for the banggood link to the miter T-Slot. I saw one on amazon that was about twice the price so think I might order a couple.

    Now, that you have done yours do you have any suggestions to getting the miter slots parallel with the blade?



  3. muf fin on November 11, 2022 at 4:58 am

    Wow such a pristine recovery ! Great editing as always !



  4. Derick Thompson on November 11, 2022 at 5:05 am

    Thank you for this – I bought pretty much the same table saw as it was all I could afford, but it is truly sub par – the top was warped out of the box and for now I just put a sheet of MDF over it, but really wanted to rebuild – your solution with cutting out the mounting point from the old top is brilliant, as I was wondering how I was going to mount it under the new table top I want to make.
    It seems I didn’t buy a table saw, just a motor and motor housing (at least it is a 2HP motor and a 10" blade 🙂



  5. ian bertenshaw on November 11, 2022 at 5:30 am

    You didn’t make a mistake Willy , you just allowed for the table top to shrink 😁



  6. MrWizards1974 on November 11, 2022 at 5:31 am

    We can just call that a adjustable T track. 😉



  7. Mike Bronsema on November 11, 2022 at 5:39 am

    Awesome vid keep it up, but where did you get that large tool @2.16 ?



  8. Jennifer Campione on November 11, 2022 at 5:39 am

    OMG!!! Perfect and exactly what I needed. You did a fantastic job of going over all the measurements, what to use for router guide (brilliant just using the t-trak) and also how to make the cut. Btw, I never comment but was compelled to tell you what a great job you did here. Thank you for spending the time creating this video!!! 😁😁😁