1. J W on March 30, 2022 at 6:24 pm

    Looks crap… I think Dremel missed a trick by way of not making it compatible with earlier models like mine (395) etc. If they are going to make accessories available for only later models they are losing out on custom, plus I think a mitre saw would be easier and quicker (and probably cheaper) to achieve wood cutting tasks…
    P.S. your clamps are not stable enough… lol… ๐Ÿ˜Ž๐Ÿ˜Ž๐Ÿ˜Ž

  2. David Latham on March 30, 2022 at 6:26 pm

    had a problem with accessory nut the thread was too small and did nit fit my dremel but worked on the snake cable

  3. busybody1 on March 30, 2022 at 6:28 pm

    Gotta be honest, that tool is already a piece of crap but the way you try to use it just made it that much worse.. thumbs down total fail, go to your room and think about what you did ๐Ÿ˜ญ

  4. Philippe PLOUCHART on March 30, 2022 at 6:30 pm

    Too awkward, complicated.

  5. Maggie Turnbull on March 30, 2022 at 6:33 pm

    That does not look like it’s working very well.

  6. Fernando Salas on March 30, 2022 at 6:34 pm

    Dremel makes wonderful toys. As a teen in the 80s I built r/c airplane made out of balsa wood. Now they amaze me with new tools they have come up with. Iam thinking of getting back into model airplanes.

  7. Angela C on March 30, 2022 at 6:35 pm

    3 / 10 for me

  8. Eren Ersan on March 30, 2022 at 6:37 pm

    Dremel MS400 is sold out because of it’s performance as you see. Dremels have no enough torque to cut. So they have failed at this attachment. That’s why you guys cannot find that anywhere.

  9. ะ˜ะฝะฝะฐ ะœัƒั€ะฐะฒัŒะตะฒะฐ on March 30, 2022 at 6:40 pm

    *We had originally tried the cordless version of this Jig Saw>>>**t.co/BwzFsC0Q1c** ย  and decided that we loved it. However since we would normally use this where plugs could be found easily we opted for the corded version and am glad we did so because it definitely has more power to it and you don’t have to worry about the battery. We tried one other cheaper brand and it just didn’t do the job like this one.*

  10. Ruben Ruiz on March 30, 2022 at 6:45 pm

    I like the demonstrations

  11. underfloor heating installer on March 30, 2022 at 6:47 pm

    unbelivabely Stupid degsin !

  12. EarlOfRednecks on March 30, 2022 at 6:50 pm

    Yikes, not the tool fore me.

  13. Bruce Ferguson on March 30, 2022 at 6:50 pm

    This attachment was never meant to cut through wood like that. It’s meant for small hobby stuff and drywall.

  14. happyjj l li on March 30, 2022 at 6:54 pm

    I am so glad I found your video. I have had this dam tool for so many years & never knew how to use it . I don’t even if I can find the little thing that goes in the end before attaching it. but Find it I will. when I bought the jigsaw I was in my 50eds now I am 70 , maybe I can use it now. it was on sale I do know it was less than $10.00 , on a table outside the store.I think now it was a good deal. thank you for showing me how to use it.

  15. Jason P. Brunke on March 30, 2022 at 6:55 pm

    Can’t find this anywhere…

  16. Plutot Crever on March 30, 2022 at 6:56 pm

    Dremel could lose their buisness with this. It should never have been sold.

  17. Sharie Dodson on March 30, 2022 at 6:57 pm

    I have had it a long time never new how to hook it up.. Thanks for showing me how. Also you said not to use on hard wood how about a gourd? thanks for the info..

  18. Ahmed Mattar on March 30, 2022 at 6:58 pm

    It did not seem to cut at all. Seems like a waste of money.
    Will not be looking for it.

  19. Kerri Schneider on March 30, 2022 at 7:01 pm

    Thanks for making the video! I decided to break mine out and couldn’t figure out why it wasn’t working…. I didn’t have that dohickey that accepts a square shaft. Now….as to where that little sucker has up and run off to….? I’m gonna set a timer for 5 minutes and if I find it before the buzzer goes off…yeah. If not, then I’ll add it to the drawer of stuff that is missing required parts. Lol.

    One of the things I liked about this is that you can put the blade on with the teeth facing in either direction. Apparently that was useful to me last time I used it, because I had a hand written note taped to it stating this. I can’t remember what I was making though. ๐Ÿค” thanks again for the handy video.

  20. Kalvin Noble on March 30, 2022 at 7:03 pm

    The design needs to be modified to have the ability to connect to the end of the Dremel Flex Shaft. This way will give it much better handling characteristics.

  21. Patrick Mahoney on March 30, 2022 at 7:03 pm

    Thanks for the video – was given a MS400 w no instructions on how to put it together with a Dremel400. Got it done – Thanks.

  22. d green on March 30, 2022 at 7:05 pm

    Would this attachment be able to accept a file ? I’m thinking it might work better as a die sander than a saw

  23. leonardo00fernandez on March 30, 2022 at 7:07 pm


  24. Mohan Krishnasamy on March 30, 2022 at 7:12 pm

    Good Morning. Thank you ๐Ÿ˜Š

  25. Simon Purefoy on March 30, 2022 at 7:14 pm

    Can these be bought in U.K. ?

  26. philanna38 on March 30, 2022 at 7:17 pm

    I’ll use my regular zigsawย  after seeing that performance.

  27. jungleowlet on March 30, 2022 at 7:21 pm

    Sir, I feel the tool should have been held perpendicular to the table for cutting, rather than at an angle. Can you try that out and let us know . Thanks.

  28. GESEPPI19 on March 30, 2022 at 7:22 pm

    A stay away tool in my opinion. Damn, I’ve never seen something cut that horrible.

  29. Geo Zero on March 30, 2022 at 7:22 pm

    Doesn’t look like it cuts very well. Flimsy.

  30. Sheila Barber on March 30, 2022 at 7:23 pm

    Won’t be buying this.