Never Seen Before !! Multifunction Device Woodworking Tool Give Huge Impact for Working

Never Seen Before !! Multifunction Device Woodworking Tool Give Huge Impact for Working

#plywoodworking #woodworking #howtomake
If you like The video Please Subscribe and share this channel!!
DONT FORGET join on Plywoodworking Tips & Trick Group on FB !!
easy for download FREEPLAN
Follow Plywoodworking

https://www.facebook.com/PlywoodworkingTipsTrick
https://www.facebook.com/groups/479435482886643/
https://www.instagram.com/plywoodworking/

15 Comments

  1. LENTERA INSPIRASI on December 8, 2022 at 12:27 am

    Sebuah karya yg luarbiasa πŸ‘πŸ‘πŸ‘



  2. Les Neilson on December 8, 2022 at 12:28 am

    I might make this for myself as I like the 45 degree references in your design and it should exceed as a marking out tool getting close to the mark. Precision I get is from dial gauges, Vernier calipers and sneaking up on the cut etc. never from pencil lines but it will make marking out much easier and useful



  3. Malcolm Marks on December 8, 2022 at 12:28 am

    Wow. Another jig.



  4. Bushman 412 on December 8, 2022 at 12:30 am

    nice video, why the left glove?



  5. Vinicius teixeira de carvalho on December 8, 2022 at 12:44 am

    only the idea of ​​the plane deserves the inscription and several likes!πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘πŸ‘



  6. Bradley Tuckwell on December 8, 2022 at 12:46 am

    Beautifully made and a very useful tool thanks for sharing



  7. Xak Li on December 8, 2022 at 12:47 am

    this ingenious young man, so far, has never produced a video I have not felt compelled to "like" . . .



  8. Henrik Paulsen on December 8, 2022 at 12:47 am

    I wouldn’t trust that one for anything requiring a high level of precision, as 0,7mm is quite a lot of slack. And with metal against wood, it will only get worse over time. It’s better to use a smaller bit and sneak up on the final width with multible cuts, than to use an oversized bit. Also, the magnets, although fairly strong, will not hold the ruler wery secure. A small bump, and the setting is off. I would suggest countersinking an allen key bolt from the side in each direction. The wood should be hard enough for the threads, otherwise use a cross threaded pin like the ones used on furniture. That way you also mitigate the slack in the groove for the ruler.
    I don’t mean to come across as a bigot, as technical designer and former fitter, finding design flaws and trying to correct them just comes natural to me.
    1:16 Always make sure the workpiece is securely against the fence at both front and back, and flat on the table. The "chicken foot" push stick is probably the worst push stick in existence for this purpose, as you have absolutely no control over your workpiece. If it’s all you have, at least use 2 so you can keep the front pushed down onto the table and somewhat pushed against the fence. The other one at the back should be centered between the fence and the blade. If it is kept too close to the fence, you risk twisting the workpiece into the blade (I see a slight wobble at about 1:17). If it is a short piece, you risk kickback before the front reaches the riving knife (NEVER cut without one).
    For shorter pieces and pushing from the back in general, I use this one from Craftswright (I made mine from 9mm plywood): https://www.youtube.com/watch?v=NOgtKbWjLlw
    For longer pieces, I make sure the front of the piece is firmly against the fence and the table, and when the front is past the riving knife, I use my left hand to hold the front down and against the fence while using the push stick on the rear.
    I plan to make other types of push sticks, like this one: https://www.youtube.com/watch?v=bJM1FFOiQ_M



  9. M.Ashraf Moustafa on December 8, 2022 at 12:53 am

    I watched several videos for you. I like your videos very much, I subscribe and like and activate the notification bell for all new videos from you. Thanks for sharing. Best regards.



  10. ExpatMousse on December 8, 2022 at 1:03 am

    Very good ideaπŸ‘πŸ» would also love to see you build that planner Jig, do you have a video on it or could you make one please?



  11. MC's Creations on December 8, 2022 at 1:05 am

    Brilliant jig, dude! Excellent work! πŸ˜ƒ
    Stay safe there with your family! πŸ––πŸ˜Š



  12. Hassan Al-Mosawi on December 8, 2022 at 1:09 am

    Thanks for sharing those tips and the make!



  13. Mick Latham on December 8, 2022 at 1:15 am

    Looks very nice.but wouldn’t a combination square do just as well?



  14. Azlan az on December 8, 2022 at 1:18 am

    Bang mau tanya,buat nempelin aluminium sheet ke top table pake lem apa ya??
    Sekalian rekomendasi brand lem nya
    Makasih



  15. Pedro Reinoso on December 8, 2022 at 1:18 am

    Donde encuentro como hisiste la adaptacion a la cepilladora