Sip 01332 Table saw, What do you get ?

Sip 01332 Table saw, What do you get ?

Welcome back to my workshop ๐Ÿ˜.

In todays video I show you my “New to me” Sip 10″ cast iron table saw ๐Ÿ˜ƒ.

I quickly run through the process of looking for a suitable saw and then look at what I finally got.

I hope this first look at the Sip 01332 10″ cast iron table saw is helpful.
The will no doubt be follow up videos of me getting this beast ready for service.

Please note:- I didn’t show any prices in this video as they are changing so rapidly….. the info would be out of date by the time you see it.

Please like and sub if you can, it means a lot to me and my channel.

Thanks for watching….. and stay safe ๐Ÿ˜๐Ÿ‘

#frankslittleworkshop #Siptablesaw #Sip01332 #Charnwood #Recordpower #Axminster #AxminsterTrade #iTECH #Laguna #scheppach #SawStop #tablesaw #castirontablesaw #toolreview #woodworkingmachine #Ragandbonebrown #AnchorDesigns

20 Comments

  1. Ray Smith on December 23, 2022 at 1:18 am

    Hi frank. Iโ€™ve got this saw but have a problem with the rise and fall worm screw. Iโ€™ve emailed sip but no reply. Iโ€™m missing the nuts off the end of the screw. At 14.52 in your video you can clearly see 2 nuts on the right end side of the worm screw. When I try to lower the blade the handle simply unscrews as nothing is there to stop it.Are these simply nuts screwed on and opposing each other so they donโ€™t come loose or is it something more technical? The parts diagram from sip is useless tbh. Thanks for any help.



  2. Ben Jaqson WorkShop on December 23, 2022 at 1:24 am

    Beautiful piece of kit. Well done on finding it, can’t wait to see you making the most of it. Where’s it going? with a 5′ guide rail it’s going to be taking pride of place. I preferred the SIP but got the Charnwood as the new SIP was a lot of money. Thanks for keeping us up to date.



  3. TheWoodfather - Mario on December 23, 2022 at 1:26 am

    New Tool Day, nice! Enjoy the upgrade Frank, it’s always fun to level up one of the key tools.
    The saw is different to mine, but it looks like we have pretty much the exact same fence. My fence stays square for about five minutes after I service it, then it is angle city. ๐Ÿ™
    I always use a speed square to double check before I cut, might be worth getting in that habit until you can trust that your one rolls and locks square. ๐Ÿ‘



  4. Dave D on December 23, 2022 at 1:30 am

    Hi Frank – I’ve been running one of these for a couple of years on a 13a fuse and it’s not blown once yet. Thanks for the video, nice to see another 01332 to compare the condition of mine with!



  5. Hand-i-Craft on December 23, 2022 at 1:31 am

    Wow, that looks the business Frank๐Ÿ‘๐Ÿ‘. Hope it works out well for what you need๐Ÿ˜€๐Ÿ‘



  6. Eldorado craftsman on December 23, 2022 at 1:32 am

    Thatโ€™s a nice bit of kit. I wouldnโ€™t be as brave to buy it second hand as Iโ€™m no good with motors of electrics. Worth it if you know what youโ€™re at though. ๐Ÿ‘๐Ÿพ



  7. Anchor Designs on December 23, 2022 at 1:37 am

    Looks to be in great condition Frank! Weirdly straight after my video i discovered mine is a 30mm bore! another great video frank! ๐Ÿป๐Ÿ™‚๐Ÿ‘



  8. Mark Jarman on December 23, 2022 at 1:38 am

    You was lucky picking that up frank. Not the end of the world to pick it up from Essex. Iโ€™m also in Essex frank. Might see you in a timber yard at some point๐Ÿ˜ฌ



  9. Outside the Box on December 23, 2022 at 1:47 am

    Thanks so much for making this video! I am currently in the process of purchasing a saw 2nd or 3rd hand identical to this one but itโ€™s called Power Super and I canโ€™t find anything about it online. Iโ€™m pretty sure itโ€™s the same machine and itโ€™s 440 GBP.
    Do you think thereโ€™s a chance that it could fit into the back of a new model Vauxhall Corsa??



  10. ลžahane bilgiler on December 23, 2022 at 1:48 am

    Hello Frank,
    You use a different table saw. Seeing its engine, I realized it was a powerful chainsaw. Thank’s for the information. See you. Big greetings. Yours sincerely, Mehmet.



  11. GedReillyHomestead on December 23, 2022 at 1:49 am

    Hi Frank I think I saw the motor plate stating 2800w, at 220/240 volts it will run at 11-12amps so a 13 amp plug should be OK. unless the motor draws more at start-up! The usual circuit breaker for a ring main is about 30amp but your garage workshop sockets might be on a 16amp breaker – still OK. (I think. It’s been a lot of years since I did any proper sparky work.) Good luck with your new saw. ๐Ÿ‘ ๐Ÿ˜Ž
    Just thought problems might occur when you try to run it along with you dust extraction, which will probably take it over the 16 amp!



  12. Fixit Fingers on December 23, 2022 at 1:51 am

    Great looing upgrade. We just got Laguna in Oz, looks nice but yeah, price is up there. Looks like you got a good deal with a bit of elbow grease.



  13. trevor B on December 23, 2022 at 1:55 am

    Looks similar to my 12inch table saw mine is a hafco SB12 by hare& Forbes here in Australia it’s got open grille wings & motor hangs out of the rear belt driven too fence & the rails for the fence look identical with mine you have to check the distance between fence & blade at front & rear as the fence doesn’t adjust parallel to the blade at the rear apart from that it’s a powerful tool i bought mine new here in Australia for $900 currently they are around $1300 looking forward to your test cuts on it cheers mate ๐Ÿ‘๐Ÿ‘๐Ÿ‡ฆ๐Ÿ‡บ



  14. Rag 'n' Bone Brown on December 23, 2022 at 1:56 am

    Sounds like you got a great deal for that (saw you comment on grumpys post!) It’ll be great when you clean it up! Looks pretty much identical to mine in the inside. Thanks for the shout out Frank, wasn’t expecting that!



  15. In the Workshop on December 23, 2022 at 2:03 am

    Very Nice table saw Frank ๐Ÿ˜๐Ÿ‘



  16. Dan - The Sidings Workshop on December 23, 2022 at 2:03 am

    Great video Frank… looks like you got a good saw, what a beast that fence and rail is huge mate ๐Ÿ‘๐Ÿ‘Œ๐Ÿ‘ looking forward to the next episode ๐Ÿ‘



  17. Grumpy's Workshop on December 23, 2022 at 2:03 am

    Looks like a great saw. I would love a proper saw like that especially one with an induction motor. So come on then spill the beans how much was it???



  18. Steve Parkes on December 23, 2022 at 2:06 am

    Thatโ€™s a beast of a saw frank, look forward to seeing up and running. ๐Ÿ‘



  19. Andy's Cornish Creations on December 23, 2022 at 2:10 am

    Hi Frank… great bit of kit that… the fence is a beast… I went down the cheap route and have regretted it ever since… great video… take care…All the best…..Andy



  20. Suj Menon DIY Builds on December 23, 2022 at 2:10 am

    Frank, thats a great powerful saw, and like the condition it is in. Pretty good inside where it really matters. Whats the plan for that small rust marks on the top?