вопрос : а нах резать / пилить две палки если суть видео заключается в их соединении с помощью гайки болта и клея?
Bufo alvariuson October 27, 2023 at 10:22 pm
I dont think the drill is supposed to be thicker than the screw
Jakobb Von October 27, 2023 at 10:28 pm
Hold up a minute, you’re telling me that you can put a screw through more than one piece of wood to actually hold them together?!?!?!
Saw Bosson October 27, 2023 at 10:28 pm
Well congrats 🎉 youve got a lot of views.
Devious RedNeckon October 27, 2023 at 10:33 pm
Nothing special 😮
avtoron October 27, 2023 at 10:35 pm
Дегенерат, зачем клей если на саморезы закрутил
EBIY KALEMon October 27, 2023 at 10:36 pm
hai teman teman
apa kabar
Robert Blahnikon October 27, 2023 at 10:36 pm
When you put a screw in that way it never cinches the 2 sections of wood correctly, which makes for a horrible glue bond. How you make it better is you first run your pilot hole as he did, which BTW is truly necessary. But then you put in the screw in each of the end pieces separate and then screw in each screw until the wood hole strips and free spins. Then with a hammer, knock each screw back out to where there is 1/4" of thread sticking out. Then butter each piece with glue. Next, align the screws to there respective holes and screw in just a little on each side to where the screws catches fresh wood. Then finish tightening them.
fexi spongeon October 27, 2023 at 10:37 pm
I hate being cynical especially with the amount of hate these guys get, but really? Come on what is this?
No. Ok? No.
Garbage , that’s off, that’s a horrible way to do it to can see that it’s off that would slip all over the place while you attempt to drill
It
Biscuit anyone ???
https://youtu.be/RGlR6YYXyM4
전혀 도움이 안되🤦🏻♂️
No wood worker would even try to glue two end grain boards together
how about a clamp?
This is the stupidest idea ever. Don’t do this. Your shit will break.
no
https://youtube.com/@user-ow8cp1vv3j
вопрос : а нах резать / пилить две палки если суть видео заключается в их соединении с помощью гайки болта и клея?
I dont think the drill is supposed to be thicker than the screw
Hold up a minute, you’re telling me that you can put a screw through more than one piece of wood to actually hold them together?!?!?!
Well congrats 🎉 youve got a lot of views.
Nothing special 😮
Дегенерат, зачем клей если на саморезы закрутил
hai teman teman
apa kabar
When you put a screw in that way it never cinches the 2 sections of wood correctly, which makes for a horrible glue bond. How you make it better is you first run your pilot hole as he did, which BTW is truly necessary. But then you put in the screw in each of the end pieces separate and then screw in each screw until the wood hole strips and free spins. Then with a hammer, knock each screw back out to where there is 1/4" of thread sticking out. Then butter each piece with glue. Next, align the screws to there respective holes and screw in just a little on each side to where the screws catches fresh wood. Then finish tightening them.
I hate being cynical especially with the amount of hate these guys get, but really? Come on what is this?
When you have to get the board stretcher…